User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            Honeywell 1885:Strain Gage Control Unit
DATE:                  06-Sep-96
AUTHOR:                User Contributed
REVISION:              0
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       23
NUMBER OF LINES:       220
CONFIGURATION:         Datron 1281
STANDARD:              Measurements Group 1550A
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-   R     N              P             M              F        W
  1.002  ASK+                                          X
  1.003  STD          Measurements Group 1550A
  1.004  IEEE         [@1281]*RST
  1.005  IEEE         [@1281]DCV AUTO
  1.006  HEAD         ÍÍ INITIAL CONDITIONS ÍÍ
  1.007  DISP         On the UUT lower board, set jumper JI to 1-3
  1.008  DISP         Also on the lower board insure J2, J3, J4, J5
  1.008  DISP         are installed.
  1.009  DISP         On the UUT upper board, set jumper J1 to C-4, and
  1.009  DISP         J2 to C-1.
  1.010  DISP         Plug the UUT into slot six of an 1858 Visicorder
  1.010  DISP         mainframe.
  1.011  DISP         Connect the test cable to channel six connector
  1.011  DISP         on the rear of the mainframe.
  1.012  DISP         Turn on mainframe.
  1.013  DISP         On the 1858 set the TIMELINE switch to OFF, and
  1.013  DISP         the GRIDLINE switch to CONT.
  1.014  DISP         Set the UUT CAL/SUPP -/0/+ switch to 0.
  1.015  DISP         ÿÿÿÿÿConnect the UUT as follows:
  1.015  DISP         PIN A (orange wire) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ[16] 1550A S+ (350ê)
  1.015  DISP         PIN C (brown wire) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ[16] 1550A S- (350ê)
  1.015  DISP         PIN D (red wire)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ[16] 1550A P+ (350ê)
  1.015  DISP         PIN B (black wire)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ[16] 1550A P- (350ê)
  1.016  DISP         Set the 1550A strain calibrator for 0,0,0.
  1.017  DISP         Connect the Datron HI/LO inputs to S+ and S-.
  1.018  DISP         While alternately switching POLARITY on the 1550A,
  1.018  DISP         adjust the 1550A ñZERO control for minimal voltage
  1.018  DISP         change on the Datron.
  1.019  DISP         Adjust the UUT BAL control for a 0 dcv reading
  1.019  DISP         on the Datron
  1.020  HEAD         {}
  1.021  HEAD         {ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»}
  1.022  HEAD         {º Excitation Voltage º}
  1.023  HEAD         {ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ}
  1.024  HEAD         ÍÍ Excitation Voltage ÍÍ
  1.025  JMP          2.001
  1.026  EVAL
  2.001  IEEE         [@1281]RDG?[D1000][I]
  2.002  ACC    20    10.000V        6P% 0.1P/
  2.003  MEME
  2.004  MEMC         V              0.25%
  3.001  DISP         Turn off 1858 and remove UUT.
  3.002  DISP         Set jumper J1 on the lower board to 2-4.
  3.003  DISP         Reinstall UUT and turn on mainframe.
  3.004  IEEE         [@1281]RDG?[D1000][I]
  3.005  ACC    20    5.000V         6P% 0.1P/
  3.006  MEME
  3.007  MEMC         V              0.25%
  4.001  DISP         Turn off 1858 and remove UUT.
  4.002  DISP         Set jumper J1 on the lower board to 1-4.
  4.003  DISP         Reinstall UUT and turn on mainframe.
  4.004  IEEE         [@1281]RDG?[D1000][I]
  4.005  ACC    20    2.500V         6P% 0.1P/
  4.006  MEME
  4.007  MEMC         V              0.25%
  5.001  DISP         Turn off 1858 and remove UUT.
  5.002  DISP         Set jumper J1 on the lower board to 1-3.
  5.003  DISP         Reinstall UUT and turn on mainframe.
  5.004  HEAD         {}
  5.005  HEAD         {ÉÍÍÍÍÍÍÍÍÍÍÍ»}
  5.006  HEAD         {º Linearity º}
  5.007  HEAD         {ÈÍÍÍÍÍÍÍÍÍÍͼ}
  5.008  HEAD         ÍÍ Linearity ÍÍ
  5.009  JMP          6.001
  5.010  EVAL
  6.001  DISP         Set the UUT TRACE switch to ZERO.
  6.002  DISP         Adjust the UUT POS control to position the DOT on the
  6.002  DISP         left most accented gridline.
  6.003  DISP         Set the UUT TRACE switch to REV.
  6.004  DISP         Set the strain calibrator for 7,0,0.
  6.005  DISP         Adjust the UUT SENS control for a deflection of 35
  6.005  DISP         gridlines (seventh accented gridline).
  6.006  DISP         Adjust the strain calibrator for 30 gridlines
  6.006  DISP         of deflection.
  6.007  MEMI         Enter the 1550A microstrain switch setting.
  6.008  MEM*         100
  6.009  ACC          60000î         0.025%
  6.010  MEME
  6.011  MEMC         î              0.5%
  7.001  DISP         Adjust the strain calibrator for 25 gridlines
  7.001  DISP         of deflection.
  7.002  MEMI         Enter the 1550A microstrain switch setting.
  7.003  MEM*         100
  7.004  ACC          50000î         0.025%
  7.005  MEME
  7.006  MEMC         î              0.5%
  8.001  DISP         Adjust the strain calibrator for 20 gridlines
  8.001  DISP         of deflection.
  8.002  MEMI         Enter the 1550A microstrain switch setting.
  8.003  MEM*         100
  8.004  ACC          40000î         0.025%
  8.005  MEME
  8.006  MEMC         î              0.5%
  9.001  DISP         Adjust the strain calibrator for 15 gridlines
  9.001  DISP         of deflection.
  9.002  MEMI         Enter the 1550A microstrain switch setting.
  9.003  MEM*         100
  9.004  ACC          30000î         0.025%
  9.005  MEME
  9.006  MEMC         î              0.5%
 10.001  DISP         Adjust the strain calibrator for 10 gridlines
 10.001  DISP         of deflection.
 10.002  MEMI         Enter the 1550A microstrain switch setting.
 10.003  MEM*         100
 10.004  ACC          20000î         0.025%
 10.005  MEME
 10.006  MEMC         î              0.5%
 11.001  DISP         Adjust the strain calibrator for 5 gridlines
 11.001  DISP         of deflection.
 11.002  MEMI         Enter the 1550A microstrain switch setting.
 11.003  MEM*         100
 11.004  ACC          10000î         0.025%
 11.005  MEME
 11.006  MEMC         î              0.5%
 12.001  HEAD         {}
 12.002  HEAD         {ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»}
 12.003  HEAD         {º CAL/SUPP Test º}
 12.004  HEAD         {ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ}
 12.005  HEAD         ÍÍ CAL/SUPP Test ÍÍ
 12.006  JMP          13.001
 12.007  EVAL
 13.001  DISP         Turn off mainframe and remove UUT.
 13.002  DISP         Change jumper J1 on the upper board from C-4 to C-2.
 13.003  DISP         Reinstall UUT and turn on mainframe.
 13.004  DISP         If necessary, readjust UUT positon for leftmost
 13.004  DISP         accented gridline.
 13.005  DISP         Set the UUT CAL/SUPP dial to 10.
 13.006  DISP         Set the UUT CAL/SUPP X1/X10 switch to X1.
 13.007  DISP         Set the strain calibrator for 0,2,0.
 13.008  DISP         Adjust the UUT SENS control for a deflection of
 13.008  DISP         10 gridlines.
 13.009  DISP         Set the UUT CAL/SUPP -/0/+ to -.
 13.010  DISP         Adjust the CAL/SUPP control for no deflection. (Dot
 13.010  DISP         on the left most accented gridline.)
 13.011  MEMI         Enter the CAL/SUPP dial reading.
 13.012  ACC          10.000mV       0.025%
 13.013  MEME
 13.014  MEMC         mV             0.05U
 14.001  DISP         Set the strain calibrator for 0,1,8.
 14.002  DISP         Adjust the CAL/SUPP control for no deflection. (Dot
 14.002  DISP         on the left most accented gridline.)
 14.003  MEMI         Enter the CAL/SUPP dial reading.
 14.004  ACC          9.000mV        0.025%
 14.005  MEME
 14.006  MEMC         mV             0.05U
 15.001  DISP         Set the strain calibrator for 0,1,6.
 15.002  DISP         Adjust the CAL/SUPP control for no deflection. (Dot
 15.002  DISP         on the left most accented gridline.)
 15.003  MEMI         Enter the CAL/SUPP dial reading.
 15.004  ACC          8.000mV        0.025%
 15.005  MEME
 15.006  MEMC         mV             0.05U
 16.001  DISP         Set the strain calibrator for 0,1,4.
 16.002  DISP         Adjust the CAL/SUPP control for no deflection. (Dot
 16.002  DISP         on the left most accented gridline.)
 16.003  MEMI         Enter the CAL/SUPP dial reading.
 16.004  ACC          7.000mV        0.025%
 16.005  MEME
 16.006  MEMC         mV             0.05U
 17.001  DISP         Set the strain calibrator for 0,1,2.
 17.002  DISP         Adjust the CAL/SUPP control for no deflection. (Dot
 17.002  DISP         on the left most accented gridline.)
 17.003  MEMI         Enter the CAL/SUPP dial reading.
 17.004  ACC          6.000mV        0.025%
 17.005  MEME
 17.006  MEMC         mV             0.05U
 18.001  DISP         Set the strain calibrator for 0,1,0.
 18.002  DISP         Adjust the CAL/SUPP control for no deflection. (Dot
 18.002  DISP         on the left most accented gridline.)
 18.003  MEMI         Enter the CAL/SUPP dial reading.
 18.004  ACC          5.000mV        0.025%
 18.005  MEME
 18.006  MEMC         mV             0.05U
 19.001  DISP         Set the strain calibrator for 0,0,8.
 19.002  DISP         Adjust the CAL/SUPP control for no deflection. (Dot
 19.002  DISP         on the left most accented gridline.)
 19.003  MEMI         Enter the CAL/SUPP dial reading.
 19.004  ACC          4.000mV        0.025%
 19.005  MEME
 19.006  MEMC         mV             0.05U
 20.001  DISP         Set the strain calibrator for 0,0,6.
 20.002  DISP         Adjust the CAL/SUPP control for no deflection. (Dot
 20.002  DISP         on the left most accented gridline.)
 20.003  MEMI         Enter the CAL/SUPP dial reading.
 20.004  ACC          3.000mV        0.025%
 20.005  MEME
 20.006  MEMC         mV             0.05U
 21.001  DISP         Set the strain calibrator for 0,0,4.
 21.002  DISP         Adjust the CAL/SUPP control for no deflection. (Dot
 21.002  DISP         on the left most accented gridline.)
 21.003  MEMI         Enter the CAL/SUPP dial reading.
 21.004  ACC          2.000mV        0.025%
 21.005  MEME
 21.006  MEMC         mV             0.05U
 22.001  DISP         Set the strain calibrator for 0,0,2.
 22.002  DISP         Adjust the CAL/SUPP control for no deflection. (Dot
 22.002  DISP         on the left most accented gridline.)
 22.003  MEMI         Enter the CAL/SUPP dial reading.
 22.004  ACC          1.000mV        0.025%
 22.005  MEME
 22.006  MEMC         mV             0.05U
 23.001  HEAD         {}
 23.002  DISP         {ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»}
 23.002  DISP         {º THIS COMPLETES THE VERIFICATION º}
 23.002  DISP         {ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ}
 23.003  END